![]() Some hardware is under sized, and some materials are inferior and having the top stripped out already is just another strike against you sometimes. I've done as you suggest here and still had blow outs. Period Features strive to be the number one source in the UK for vintage homeware and traditional hardware products for period properties, and to always provide an excellent, friendly service. But it often isn't an option for a variety of reasons. Dark Bronze - Drawer Pull - 100mm - Face Fix A well proportioned drawer pull (also know as a cup. That is always my first choice for dealing with stripped out stuff because to me it is the best, and easiest fix. Also I've drilled out plenty then retapped it to the next size up. Depends on the situation, what I'm looking for etc. I've also filled holes with braze, or even weld then done the whole drill tap routine on it. Of course the simplest method is just throw some epoxy in there, put it together and wait for it to dry, but that has its drawbacks if you ever want to disassemble hardware. I've filled stripped holes with JB Weldit and then redrilled and retapped them. But that method does require the most equipment. In my workshop I usually cut threads straight off, chamfer on a grinder, then wire wheel them myself. If you don't have that tool to cut screws there is a trick to cutting threads with a hack saw where you pull up on the unsupported end right before you cut through and threads come out so you can use them. But, both of these are "desperate measures" for getting out of a special, very difficult problem. If the screw does not grab enough threads after cutting, you could drill out the back of the door or the drawer front using about a 1/2 inch bit to gain some length. If your knob is still too loose after cutting to length, you could add extra washers to the head to take up the extra and make it tight. Cutting a new, longer screw can get you out of a difficult situation. You will have saved your knob or pull, which may no longer be available new in the pattern you have on the rest of your cabinets. Some of the old stripped threads are only partially stripped and will add some additional gripping power. See also the second photo, which shows the original screw in the cabinet door and the third photo, which shows the new freshly cut replacement screw. ![]() It is just enough longer to catch fresh threads in the stripped cabinet knob or pull. On the right you see a freshly cut replacement screw. It’s the cheapest method and made the biggest difference for me.On the left you see an original cabinet hardware screw. If you’re not sure where to start, I recommend the baking soda and boiling water. My drawer pulls didn’t turn out perfect, but there are SO MUCH cleaner than before! I didn’t even know they had a pattern before I started cleaning them! Each of the cleaning methods I used worked well to remove the rust and grime from these antique beauties. You’ll need an air compressor for sandblasting as well as a sandblaster, but this can be a great way to give your drawer pulls a new look. If your metal drawer pulls are rusted, you can opt to sand blast them. Related: Troubleshooting Drawer Slides Sandblasting It will leave a green tint anywhere that it is not rubbed off. Be sure to scrub all of the Brasso off of the hardware.I wore gloves again because I wasn’t sure if the Brasso would irritate my hands.Make sure you’re in a well ventilated area and consider wearing a breathing mask.For pulls with a lot of rust, use a toothbrush to get the Brasso into the small crevices and knock off the rust.Rub the Brasso into the drawer pull with the rag.Squirt a little bit of Brasso onto a cloth rag.For drawer pulls that still had some rust and dirt I used a toothbrush to rub the Brasso in and gently knock the rust off. The Brasso worked best on hardware that was already mostly clean. It has a very strong chemical smell that left me with a headache even though I only used it for about 20 minutes or less in an area with an open window and fan. It was my least favorite cleaning method because of the chemical smell of Brasso. ![]() I accidentally scrubbed some of the finish off of the raised sections of these drawer pulls while trying to clean out the grooves.īrasso was the last thing I used on my drawer pulls and it did a great job of shining them up. ![]() These are t he same gloves I wear for staining wood and they held up great against the Bar Keepers Friend. I don’t know if it’s necessary to wear gloves, but I did just to make sure the powder wouldn’t irritate my hands.Best Double-Sided Tapes for Woodworking.Best Deck Stains for Pressure Treated Wood.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |